The EVO MFG 3.5â€ JLU High Clearance Long Arm kit will like your JLU 3.5â€s. Through specificallyÂ designed bracketry we accomplish the ultimate in suspension and chassisÂ clearance, larger wheel travel ability, optimal suspension geometry withÂ increased ride quality. Clearance, ride quality, performance and ease of installation was ourÂ focus in creating this long arm suspension system.Â The front arms mountÂ tucked up inside nearly flush with the bottom of the frame mountingÂ inches above the stock front lower mounting bracket.Â The rear mountingÂ locations for the long arm are on the side of the frame, above theÂ bottom giving inches of clearance over the factory locations as well.Â Â Keeping optimal geometry while maintaining as much clearance wasÂ critical in the design of this system.Â In doing so, not only did weÂ raise the rear control above the frame but we raised its mounting at theÂ rear axle by multiple inches as well.Â This allows for an incredibleÂ ground clearance increase but just as importantly retaining flat andÂ optimal control arm angles giving ideal ground clearance, smooth rideÂ quality and long travel ability. The mounting brackets are specifically designed to require no exhaustÂ cutting on 3.6L Jeep Wrangler JLUâ€™s (minor grind/clearance to flangeÂ required) and have full length hard-face mounting surfaces that weld toÂ your frame giving redundant and ample welding area and strength to theirÂ mounting.Â The mounting brackets align to the frame simply usingÂ existing factory holes giving complete assurance of proper locatingÂ during install.Â Simply bolt brackets up to frame with existing hardwareÂ and weld them in place. These kits come with a set of 3.5â€ Plush Ride Lift springs specific to each corner which will keep the Jeep Wrangler JLU more level side to side and will maintain a unique and compliant ride quality. EVO MFG Long Arm joints feature Johnny Joints on both ends of theÂ control arms for restriction free articulation and motion with noÂ wearable and limited bond rubber.Â All long arms come complete with EVO1Â on vehicle adjuster making alignment a snap allowing for the ability toÂ adjust control arm lengths while completely installed on the vehicle atÂ all times.Â All EVO MFG lower long arms are built with strength in mind.Â These arms are made from industry leading 2.0â€ x .281â€ wall Steel DOMÂ Tubing. Include in these kits is front brakeline extension brackets, Rear swaybar endlinks and front and bumpstop extensions. Cutting, grinding and welding of frame brackets required. The EVO MFG 3.5â€ High Clearance Long Arm kits require no driveshaft or exhaust modifications (your shock choice may require this, contact manufacturer to be sure). Option of retaining factory shocks, maintaining wheel travel with use of shock extensions (part number EXT kits) or without shock extensions to allow for use of your choice of aftermarket 3/5â€ lift shocks. EVO3015K kits come with EVO SPEC King 2.5â€ Remote Reservoir shocks all 4 corners. 3.5â€ lift is based on increase of our 4 Door Rubicon.Â 4 Door Sport and Sahara Models will see slightly higher increases over stock and will match overall lift height of a Rubicon Model.Â 2 Door Models (all) will see slightly higher increases in lift.Â Increases will vary. Note:Â Â Depending on actual tire variances and sizes, Some minor factoryÂ inner liner plastic may need to trimmed/removed to fully clear some tiresÂ under compression.Â These kits require wheel spacers or aftermarket wheels with smaller backspacing. Adjustable Front Trackbar is required to complete proper installation, Front and rear adjustable trackbars are included with PLUS â€œPâ€ kits..
Payment & Security
Your payment information is processed securely. We do not store credit card details nor have access to your credit card information.